• 18,739 - 19,290 lbs Operating Weight
  • 65.5 @ 1950 rpm Horsepower
  • 0.12 - 0.44 yd¬≥ Bucket Capacity

PC88MR-10

The PC88MR-10 is a link between minis and mid-size excavators.  The PC88MR-10 has a swing boom, tight tail swing, three track options and backfill blade like a mini but is built to have the reliability and durability of larger excavators.

PC88MR-10 Walkaround

FEATURES

Komatsu Diesel Oxidation Catalyst (KDOC)

The new Komatsu Diesel Oxidation Catalyst (KDOC) has an integrated design that does not interfere with daily operation. This smart and simplified system removes soot using 100% "passive regeneration" without the need for a Diesel Particulate Filter. The KDOC is a simple design and does not have a scheduled service interval like a DPF and is designed for long life with no scheduled maintenance required. For owners, this means lower owning and operating costs due to less complexity and seamless operation.

Newly designed Variable Flow Turbocharger

A newly designed variable flow turbocharger features simple and reliable technology that varies the intake airflow. This provides optimum air flow under all speed and load conditions producing cleaner exhaust gas without sacrificing power and performance.

Efficient Hydraulic System

The PC88MR-10 uses a Closed-center Load Sensing System (CLSS) that improves fuel efficiency and provides quick response to the operator's demands.

The PC88MR-10 also introduces new technology to enhance the engine and hydraulic pump control. This total control system matches the engine and hydraulics at the most efficient point under different load conditions. There have also been improvements in the main valve and hydraulic circuit to reduce hydraulic loss, resulting in higher efficiency and lower fuel consumption.

Reduced Up To 4% Fuel consumption*
*vs PC88MR-8 Based on typical work pattern collected via KOMTRAX

High Rigidity Work Equipment

Booms and arms are constructed with thick plates of high tensile strength steel. In addition, these structures are designed with large cross-sectional areas and large one piece castings in the boom foot and the boom tip. The result is work equipment that exhibits long term durability and high resistance to bending and torsional stress.

Swing Boom

The swing boom allows the PC88MR-10 to work where a standard boom excavator could not.

Rear View Monitoring System

The operator can view the rear of the machine with a color monitor screen.

Standard Blade

Every PC88MR-10 comes standard with a 2332mm 7'7" blade. A wide angle blade is also available as an option.

Pattern Change Valve Standard

A pattern change valve is conveniently located below the cab, making switching from excavator controls to backhoe controls quick and easy.

Specifications

Engine

Model Komatsu SAA4D95LE-6*
Type Water cooled, 4-cycle, direct injection
Aspiration   Variable flow, turbocharged, air-to-air aftercooled EGR
Number of Cylinders   4
Piston displacement 3.26 ltr 199 in³
Horsepower @ 1900 rpm:
SAE J1995 / Gross 50.7 kW 67.9 HP
ISO 9249 / SAE J1349 / Net 48.8 kW 65.5 HP
Rated rpm   1950
Governor   All-speed control, electronic
Lubrication system:    
Method   Gear pump, force-lubrication
Filter   Full-flow
Air cleaner
  Air cleaner, double element and auto dust evacuator
*EPA Tier 4 Final emissions certified    

Hydraulics

Type - HydrauMind (Hydraulic Mechanical Intelligence New Design) system, closed-center system with load sensing valve and pressure compensated valve

Main pump:

Pumps for   Boom, arm, bucket, and travel circuits
Type
Variable capacity piston type, axial piston
Maximum flow 160 ltr/min
42.2 gal/min
Pumps for   Swing and blade
Type   Fixed displacement gear
Maximum flow 70 ltr/min 18.5 gal/min
Hydraulic motors:

Travel
2 x piston motor with parking brake
Swing
1 x axial piston motor with swing holding brake
Relief valve setting:    
Implement circuits 26.5 MPa 270 kgf/cm2
3,844 psi
Swing circuit
21.1 MPa 215 kgf/cm2
3,060 psi
Pilot circuit 3.2 MPa 33 kgf/cm2
464 psi
Blade circuit (Raise) 12.7 MPa 130 kgf/cm2 1,842 psi
Blade circuit (Lower) 21.1 MPa 215 kgf/cm2 3,060 psi
Hydraulic cylinders (Number of cylinders): bore x stroke x rod bore x stroke x rod
Boom (2) 115 mm x 988 mm x 65 mm 4.53" x 38.9" x 2.56"
Arm (1) 100 mm x 861 mm x 60 mm 3.9" x 33.9" x 2.36"
Bucket (1) 90 mm x 710 mm x 55 mm 3.54" x 27.95" x 2.17"
Swing (1) 120 mm x 638 mm x 60 mm 4.72" x 25.12" x 2.36"
Blade (1) 130 mm x 200 mm x 65 mm 5.12" x 7.87" x 2.56"
Auxiliary hydraulics:    
Auxiliary hydraulic flow 125 ltr/min
33.0 gal/min
Relief 26.51 MPa
3,830 psi
Breaker mode 80 ltr/min
21.1 gal/min
Relief in breaker mode 17.17 MPa
2,490 psi

Drives and Brakes

Steering control       Two levers with pedals
Drive method   Fully hydrostatic
Maximum drawbar pull 66.9 kN 6820 kgf
15,040 lbf
Maximum travel speed:    
High 5 km/h
3.1 mph
Low 3 km/h
1.9 mph
Service brake   Hydraulic lock
Parking brake    Mechanical discs 

Swing System

Driven by  Hydraulic motor 
Swing reduction
Planetary gear
Swing circle lubrication  Grease-bathed 
Swing lock  Mechanical disc brake
Swing speed 10 rpm

Undercarriage

Center frame  X-frame leg
Track frame  Box-section 
Track Type Sealed
Track adjuster  Hydraulic 
Number of Shoes
39 each side
Number of carrier rollers       1 each side 
Number of track rollers
5 each side 

Coolant & Lubricant Capacity (Refilling)

Fuel tank 125 ltr 33.0 U.S. gal
Radiator  13 ltr  3.43 U.S. gal
Engine 11.5 ltr 3.04 U.S. gal
Final drive, each side     1.1 ltr 0.29 U.S. gal
Swing drive 2.8 ltr 0.74 U.S. gal
Hydraulic tank  56 ltr 14.8 U.S. gal

Operating Weight (approximate)

Operating weight includes 3405 mm 11'2" one-piece boom, 2100 mm 6'11" arm, SAE heaped 0.2 m3 0.26 yd3 bucket, blade, rated capacity of lubricants, coolant, full fuel tank, operator, and standard equipment.

Track Shoes Operating Weight Ground Pressure
Road liner
450 mm 18"
8720 kg
19,224 lb
38.2 kPa / 0.39 kg/cm2
5.54 psi
Triple grouser
450 mm 18"
8580 kg
18,916 lb
38.2 kPa / 0.39 kg/cm2
5.54 psi
Triple grouser
600 mm 24"
8750 kg
19,290 lb
29.4 kPa / 0.30 kg/cm2
4.26 psi
Rubber shoe
450 mm 18"
8500 kg
18,739 lb
37.3 kPa / 0.38 kg/cm2
5.41 psi

 

Standard

  • 2320 mm 7'7" blade
  • Alternator, 35 Ampere, 24V
  • AM/FM radio
  • Automatic engine warm-up system
  • Automatic air conditioner/heater
  • Auxiliary input (3.5mm jack)
  • Battery disconnect switch
  • Converter, (2) x 12V
  • Counterweight, 805 kg 1,775 lb
  • Dry type air cleaner, double element
  • Electric horn
  • EMMS monitoring system
  • Engine, Komatsu SAA4D95LE-6
  • Engine overheat prevention system
  • Extended work equipment grease interval
  • Fan guard structure
  • Fuel system pre-cleaner 10 micron
  • Hydraulic control unit, 1 actuator
  • Hydraulic track adjusters
  • KOMTRAX®
  • Large LCD color monitor, high resolution
  • Lock lever 
  • Mirrors, (LH and RH)
  • Operator Protective Top Guard (OPG), Level 1
  • Pattern change valve (ISO to BH control)
  • PPC hydraulic control system
  • Pump/engine room partition cover
  • Radiator and oil cooler dustproof net
  • Rear reflectors
  • Rearview monitoring system (1 camera)
  • Revolving frame undercovers
  • ROPS cab
  • Seat belt, retractable, 76mm 3"
  • Seat belt indicator
  • Secondary engine shutoff switch
  • Service valve
  • Shoes, road liner, 450 mm 18"
  • Skylight
  • Slip resistant foot plates
  • Starter motor, 4.5kW
  • Suction fan
  • Thermal and fan guards
  • Working lights, 2 cab/1 boom LH
  • Working mode selection system                           

Optional

  • Arms, 2100 mm 6'11" arm assembly
  • Boom, 3405 mm 11'2" assembly with auxiliary piping
  • Power Angle 4 Way Blade (2296 mm 7'6")
  • Shoes, rubber shoe, 600 mm 24"
  • Shoes, triple grouser, 450 mm 18"
  • Shoes, triple grouser, 600 mm 24"
  • Wide blade 2470 mm 8'1" (requires 600 mm 24" shoes)